2011 Land Pride RC3615
The RC3615 and RCM3615 Series Rotary Cutters provide excellent cutting performance on gently sloping or slightly contoured right-of-ways, pastures, set-aside-acres, or row crop fields. The 15' cutting width and ability to cut weeds and brush up to 2" in diameter make them well suited for these applications.
The 36 Series offers a pull-type self leveling tongue with a clevis hitch for attachment to 50-160 hp tractors, and features a Cat. 5 main driveline. Safety guards around the cutter are offered in either chain or rubber.
Surpassed rugged industry standards; All Land Pride Rotary Cutters have been designed and tested and meet rigorous voluntary testing procedures.
Mostly factory assembled; Arrives for quick and easy set-up. Minimal time is wasted setting or prepping the unit.
5 Year gearbox warranty; Shows confidence in gearbox integrity.
Gearbox seal protection; Gearbox bottom seal protection for longer bearing life.
Smooth Top Design; Allows for easy cleaning of deck.
Low tongue weight; Ideal for smaller HP tractors by reducing the amount of weight on the drawbar.
Narrow tongue construction; Allows for a tighter turning radius.
Input Driveline: Cat. 5 CV; Driveline is matched just right for capacity of tractor. Constant velocity (CV) U-joint allows for 80 degree turns without doing damage to the driveline.
Wing driveline: Cat. 4 with slip-clutch; Driveline is sized right for the intended cutting capacity. Slip-clutch will slip under load instead of twisting the driveline. (Optional Cat. 5 driveline is available.)
Slip-clutch drivelines; Slip-clutches are designed to slip to minimize twist damage to the driveline profiles.
High Blade tip speed; Allows clean cutting of material.
6” Blade overlap; Eliminates skipping during turns.
Left wing rotates clockwise; Better discharge of material. Picks up tractor tracks.
3/16” Round stump jumper; Standard thick stump jumper material keeps damage to a minimum.
1/4” Sidewall thickness; Increased thickness reduces damage from objects being thrown into deck sidewalls.
Self-leveling hitch; Reduces drawbar wear by keeping hitch level while going through ditches.
Hinged wing sections; Allows cutter to follow terrain. Ideal for rough ground where hillsides, ditches and hollows can cause uneven cutting.
1” Solid hinge rods; Larger diameter hinge rod gives greater strength to the cutter from front to rear, and in the hinge area itself.
Wing transport locks; Wing transport locks securely hold the wings in the folded position in case of hydraulic failure.
Enclosed front to rear dual leveling rods; Dual leveling rods enable the cutter to pull equally on the rear axle during travel over rough terrain.
5-Bolt hubs; 5-Bolt hubs makes the wheel assembly more durable and longer lasting.
Spring cushioned center-axle; Protects unit from bumps and ground shock.
Replaceable wheel spindles; Wheel spindles can be replaced when damaged without replacing the entire axle assembly.
Wheel options; Laminated tires: Eliminates flats. Airplane tires without foam filling: Give better cushion while transporting. Airplane tires with foam filling: Give better cushion while transporting and can’t go flat. 15" Wheel rims: Can mount your own tires.
Double swivel clevis hitch; Great for uneven terrain, reduces drawbar wear. Hitch pivots freely up and down and pivots about the tractor drawbar.
Bar-tite hitch; Ideal hitch for extreme conditions. Clamps tight to the drawbar eliminating any drawbar wear. Hitch pivots freely up and down and pivots about the tractor drawbar.
2011 Land Pride RC3615
- (Input Driveline 540 & 1000 PTO) - ASAE Category 5 with constant velocity u-joint or conventional (non-cv) u-joint
(Intermediate & Wing Drivelines) Standard - Category 4 with Slip-Clutch
- (Overall) - 15’-5 3/4” (With center deck raised fully up)
- (Overall) - 15’-9”
(Minimum Transport) - 7’-11 3/4”
- (Machine) - Hitch weight = 1,300 lbs
Total weight = 3,840 lbs.
- Cutting Capacity
- 2 1/2”
- (Deck Material) - 10 gauge
(Side Skirt) - 1/4"
- Deck Height
- Blade Tip Speed
- At 540 RPM Center Blades = 15,268 FPM & Wing Blades = 15,000 FPM
At 1000 RPM Center Blades = 15,578 FPM & Wing Blades = 14,620 FPM
- - 6 (2 per Carrier) 1/2” x 4” Heat Treated
Free Swinging Alloy Steel with Uplift
(Bolt) Keyed with hardened flat washer & lock nut
(Stump Jumper / Blade Holder) 3/16" Thick round dish shaped pan, reinforced with 1" x 4" blade bar
- (Wing Hydraulics) 2 1/2" x 12" hydraulic cylinders, hoses & fittings
(Wing Transport Protection) Wing Transport Locks
- (Gear Box) - Gear Lube 80-90W EP
- Gear Box
- (Horsepower) - 540 RPM or 1000 RPM
160 HP Divider
110 HP Center & Wings
- Skid Shoe
- Wing Deck: 1 Replaceable shoe per wing
Center Deck: 2 Replaceable shoes
- (Hydraulics) 3" x 8" hydraulic cylinder, hoses, fittings & stroke control spacers
- Cutting Height
- 2” - 14”
- Number Wheels
- 6 - Wheels: 4 on transport axle and 1 on each wing axle
- (Weight) 1,240 lbs.
(Types) Standard Clevis, Double Swivel Clevis, Bar-Tite, Ball or Pintle Hitch
(Jack) - Standard (5,000 lbs.)
- Cutting Width
Power Take-Off (PTO)
- (Min.) 50